The following is an overview of the user manual for the Z-Wave product Connect Smart Deadbolt (BE469ZP)from Schlage . To view other Z-Wave products and manuals from Schlage follow that link.
Overview
The lock comes preprogrammed with two access codes and can hold up to 30 unique codes for family members and trusted friends. The fingerprint-resistant touchscreen helps access codes stay private, minimizing tell-tale wear that can tip off possible intruders.
The Schlage Connect Smart Deadbolt is battery-powered with a low battery warning that gives you weeks of advanced notice before it runs out. With guaranteed fit on standard doors, it’s easy for homeowners to install in minutes with just a screwdriver. The touchscreen continues to work in the event of a power outage, so you don’t have to worry about getting locked out – plus, a back-up key is included with the lock for peace of mind.
The Schlage Connect Smart Deadbolt incorporates Z-Wave Plus S2 technology, an enhanced security protocol that features an additional layer of AES encryption of wireless signals. The Z-Wave technology allows you to integrate your exterior door locks with other Z-Wave smart home devices, such as cameras, motion detectors, lights and thermostats, bringing the safety, simplicity and style of Schlage to your smart home.
Security
As a Z-Wave Plus certified product, Connect Smart Deadbolt supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Access Control
Features
Schlage describes Connect Smart Deadbolt as having the following features:
- Battery powered using AA batteries
- Battery Quantity
- Supported Notification Types
- Door Lock Type
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
One-button Add lock to Z-Wave Network (Inclusion)
1. Place your home automation system or panel into the “Add” or Inclusion Mode (Refer to the respective documentation for that specific home automation system or panel device for details).
2. Remove the battery cover of the deadbolt.
3. Press then release the button on the PCB.
4. An LED will flash amber indicating the “Add” or Inclusion process is in progress.
• If the Security Scheme is Security 2 (S2), verify the DSK of the lock at the Z-Wave Controller. The PIN Code portion of the Z-Wave DSK will be needed.
5. When a green LED turns ON, the “Add” or Inclusion has completed successfully.
6. If a red LED turns ON, try repeating steps 1-3
Interactive Instruction for Add
https://instructions.allegion.com/instr/86/2543
One-button Remove lock from Z-Wave Network (Exclusion)
1. Place your home automation system or panel into the “Remove” or Exclusion Mode (Refer to the respective documentation for that specific home automation system or panel device for details).
2. Remove the battery cover of the deadbolt.
3. Press then release the button on the PCB.
4. An LED will flash amber indicating the “Remove” or Exclusion process is in progress.
5. When a green LED flashes 3 times, the “Remove” or Exclusion process is completed successfully.
6. If a red LED turns ON, try repeating steps 1-3
Interactive Instruction for Remove https://instructions.allegion.com/instr/86/2581
Factory reset Connect Smart Deadbolt
Steps for One-button Factory Default Reset
1. Remove the battery cover of the deadbolt
2. Press and hold the button on the PCB for 7 (seven) seconds.
While holding the button pressed, after 1 sec LED will be lit for 2 sec. and turn OFF; continue to press and hold the button until the LED will be lit again and release the button.
3. The LED will blink red three times and the green check on the touchscreen will blink if the Factory Default Reset is successful.
4. To check that the lock was reset, press the Schlage Button and enter one of the Default User Codes. If the reset was successful, the Default User Codes will unlock the deadbolt.
NOTE: Please use this procedure only when the network primary controller is missing or otherwise inoperable.
Please note that this is a user manual Connect Smart Deadbolt from Schlage is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Connect Smart Deadbolt and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.