The following is an overview of the user manual for the Z-Wave product J-Series by Z-Wave Keypad Deadbolt (JBE109)from Schlage . To view other Z-Wave products and manuals from Schlage follow that link.
Overview
The lock comes preprogrammed with two access codes and can hold up to 30 unique codes for family members and trusted friends. The fingerprint-resistant touchscreen helps access codes stay private, minimizing tell-tale wear that can tip off possible intruders.
The J-Series by Schlage Z-Wave Deadbolt is battery-powered with a low battery warning that gives you weeks of advanced notice before it runs out. With guaranteed fit on standard doors, it’s easy for homeowners to install in minutes with just a screwdriver. The touchscreen continues to work in the event of a power outage, so you don’t have to worry about getting locked out – plus, a back-up key is included with the lock for peace of mind.
The J-Series by Schlage Z-Wave Deadbolt incorporates Z-Wave Plus S2 technology, an enhanced security protocol that features an additional layer of AES encryption of wireless signals. The Z-Wave technology allows you to integrate your exterior door locks with other Z-Wave smart home devices, such as cameras, motion detectors, lights and thermostats, bringing the safety, simplicity and style of Schlage to your smart home.
Security
As a Z-Wave Plus certified product, J-Series by Z-Wave Keypad Deadbolt supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Access Control
Features
Schlage describes J-Series by Z-Wave Keypad Deadbolt as having the following features:
- Battery Quantity
- Battery powered using AA batteries
- Door Lock Type
- Supported Notification Types
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
One-button Remove lock from Z-Wave Network (Exclusion)
1. Place your home automation system or panel into the “Remove” or Exclusion Mode (Refer to the respective documentation for that specific home automation system or panel device for details).
2. Remove the battery cover of the deadbolt.
3. Press then release the button on the PCB.
4. An LED will flash amber indicating the “Remove” or Exclusion process is in progress.
5. When a green LED flashes 3 times, the “Remove” or Exclusion process is completed successfully.
6. If a red LED turns ON, try repeating steps 1-3
Interactive Instruction for Remove https://instructions.allegion.com/instr/86/2581
Factory reset J-Series by Z-Wave Keypad Deadbolt
1. Press and hold the enrollment button.
The led will light solid amber.
2. After about 8 seconds of holding the
button, the amber light will turn off.
Release the button. Successful FDR is
indicated by 3 long green blinks and 3
long beeps.
3. You must enter a valid user code.
Lock will enter auto-handing routine,
locking and unlocking several times.
Auto-handing is complete when lock
movement stops.
One-button Add lock to Z-Wave Network (Inclusion)
1. Place your home automation system or panel into the “Add” or Inclusion Mode (Refer to the respective documentation for that specific home automation system or panel device for details).
2. Remove the battery cover of the deadbolt.
3. Press then release the button on the PCB.
4. An LED will flash amber indicating the “Add” or Inclusion process is in progress.
• If the Security Scheme is Security 2 (S2), verify the DSK of the lock at the Z-Wave Controller. The PIN Code portion of the Z-Wave DSK will be needed.
5. When a green LED turns ON, the “Add” or Inclusion has completed successfully.
6. If a red LED turns ON, try repeating steps 1-3
Interactive Instruction for Add
https://instructions.allegion.com/instr/86/2543
SmartStart location
SmartStart QR code's location as follows: Inside battery cover
N/A
Please note that this is a user manual J-Series by Z-Wave Keypad Deadbolt from Schlage is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have J-Series by Z-Wave Keypad Deadbolt and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.