Categories

Aeotec

Atrim

SmartThings

Z-Wave Products

Door Sensor (STW-W3320WU) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Door Sensor (STW-W3320WU)from Siterwell Technology. To view other Z-Wave products and manuals from siterwell follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
Siterwell Door Sensor
SKU Code
STW-W3320WU
Description
Door sensor is an intelligent security equipment that can transmit the Z-Wave network which has particular frequency. In the Z-Wave network communications, door sensor can be connected to any Z-Wave main controller (ex, SiterOne tablet). The door sensor can send messages to the Z-Wave main controller, and realize association with other devices through the Z-Wave main controller. Different countries or areas, the radio frequency is different. In the communication with the Z-Wave main controller, the door sensor can send messages to the Z-Wave main controller, but it cannot receive messages from the Z-Wave main controller. When alarm is triggered, the door sensor sends messages to the Z-Wave main controller, the Z-Wave main controller will displays the current status of door sensor, so the door sensor can associate with other devices. Door sensor is battery powered, is small and can be installed on the window or door easily. When the door or window is open, the door sensor is triggered and linkage alarm realized.
Version #
HW: 65 FW: 3.61 was the version certified
Certification #
ZC10-17085748
Certified
2017-08-25T21:34:28.911351
Z-Wave Version
6.51.06

Security

As a Z-Wave Plus certified product, Door Sensor supports Z-Wave S2 security. The following security modes are directly supported:

    Features

    siterwell describes Door Sensor as having the following features:

    • Battery powered using CR2(3.0V) batteries
    • Supported Notification Types
    • Color
    • FLiRS capable
    • Supports Network Wide Inclusion
    • Supports Z-Wave Explorer Frames
    • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

    Installation instructions

    Add Door Sensor to Z-Wave Network
    The door sensor can be added to the Z-Wave network by pressing the code button.
    Disassemble the door sensor main body and insert the battery. Make sure the device is located within the direct range of the controller.
    Set the main controller SiterOne into the adding mode (see mail controller’s operating manual).
    Quickly, triple click the code button, LED light will flash for 5 times.
    Door sensor will be detected and added in the Z-Wave network.
    Wait for the main controller to configure the sensor.

    Remove Door Sensor from Z-Wave Network
    Make sure the sensor is inserted with battery.
    Set the main controller into the remove mode (see main controller’s operating manual).
    Quickly, triple click the code button, LED light will flash for 5 times.
    Wait for the main controller to remove the sensor.

    Factory reset Door Sensor

    Restore Door Sensor to Factory Default
    Reset will delete all information on the Z-Wave network or Z-Wave controller, and restore the sensor to factory default settings.


    Remove the cover of door sensor main body.
    Make sure the sensor is inserted with battery.
    Press and hold the reset button for 10 seconds, LED light will flash red for 1 time.
    Release the button.
    Note: use the reset procedure only when the primary controller is missing or inoperable.

    NOTE
    When the Door Sensor is being restored to factory default settings, please make sure the battery is inserted.

    Please note that this is a user manual Door Sensor from Siterwell Technology is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Door Sensor and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.