The following is an overview of the user manual for the Z-Wave product SiterOne (STW-GS190B)from Siterwell Technology. To view other Z-Wave products and manuals from siterwell follow that link.
Overview
Security
As a Z-Wave Plus certified product, SiterOne supports Z-Wave S2 security. The following security modes are directly supported:
Features
siterwell describes SiterOne as having the following features:
- Communications Connections
- Firmware updatable via a compatible Z-Wave gateway
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
To exclude a Z-Wave device from the network:
- Navigate to the setting Menu
- Enter the Rooms Menu, select the device want to exclude and enter setting page.
- At the device editing page, tap Exclude device.
Trigger the device on the network, For example, if you are excluding a Z-Wave light, turn the light ON.
When the system successfully excludes the device, it will show Exclude Successfully.
Tap OK to return to the Room page.
To include a Z-Wave device to the network: (this process is also called ""replicate the information on a new controller"")
- Navigate to the setting Menu
- Enter the Rooms Menu, tap Add Device
- Select device type (if your device is not on the list ex, other controller. Select any of them and continue) and press Next
Controller start to include device.
Trigger the device. For example, if you are adding a Z-Wave light, turn the light ON. When the system discovers a device, it will show Including.
The included device appears in the Include Device Page, and it will show Include Successful. It can enter device name in the naming box.
On the naming box, enter a new device name. For example, enter: Light. After setup device name, tap Next it will go to the done page.
Tap Done. The system will show you what added in the Room.
The device will be list in the room.
SiterOne can be added to an existing Z-Wave controller as a “secondary/inclusion” controller. (this process is also called ""copy"" or ""replication"").
To include controller as a secondary/inclusion controller for an existing Z-Wave network:
Note:
a. If a SiterOne does not belong to any Z-Wave network, and another controller try to remove the SiterOne, it requires 30 seconds to complete the remove process.
b. If a SiterOne has been added into another controller, but the controller does not sent association_set commands, it requires 30 seconds to complete the add process.
- Navigate to the setting menu
- Enter the Setting Menu, and tap the Z-Wave page.
- Enter PIN code: default is 1234
- At the Z-Wave setting page, tap Learn mode.
The SiterOne enter Learn mode, and waits for a signal from the primary SiterOne.
After the include done, it will show Successfully. Tap OK.
Click the power button on the tablet. It is on the upper-right hand side.
Factory reset SiterOne
Reset SiterOne will remove all Z-Wave device and reset the controller status to factory default.
If this SiterOne is the primary controller for your network, reset controller will result in all added devices in your network being orphaned and you have to force exclude all devices and then add them again.
If this SiterOne is a secondary controller in the network, reset controller will reset this controller only , so the primary controller will no longer see the secondary controller.
- Navigate to the setting Menu
- Enter the Setting Menu, and tap the Zwave page.
- Enter PIN code: default is 1234
- At the Z-Wave setting page, tap Reset Controller
- At the Reset Controller Dialog, tap Reset
While the controller is being reset, it will show Reseting
When the controller is reset, it will show Successfully. Tap OK and the reset is done.
Please note that this is a user manual SiterOne from Siterwell Technology is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have SiterOne and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.