Categories

Aeotec

Atrim

SmartThings

Z-Wave Products

Wireless Water Leak Alarm (GS156B) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Wireless Water Leak Alarm (GS156B)from Siterwell Technology. To view other Z-Wave products and manuals from siterwell follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
Wireless Water Leak Alarm
SKU Code
GS156B
Description
The water alarm is an intelligent security equipment that can be controlled by the Z-Wave network which has particular frequency. The water alarm can be connected to any Z-Wave main controller. Different countries or areas, the radio frequency of the Z-Wave is different. This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. In the Z-Wave network communications, the water alarm can communicate with other devices associated. When the water leak is detected, the sensor will send messages to the main controller, and then the alarm sound. Through the Z-Wave network, the devices associated can response after water leak is detected, For instance, the water valve can be turned off and the alarm device can be triggered. Through the Z-Wave network controller, you can get the status of the sensor, such as battery level, also you will be notified when the water is leaking.
The water alarm is small and battery powered, it works on the hard or soft surfaces, such as carpet, floor etc. when water leak cause the two sensing probes to be short circuit, the water alarm will sound.
Version #
HW: 255 FW: 1.01:01.01 was the version certified
Certification #
ZC10-17035476
Certified
2017-03-14T01:10:37.445418
Z-Wave Version
6.61.00

Security

As a Z-Wave Plus certified product, Wireless Water Leak Alarm supports Z-Wave S2 security. The following security modes are directly supported:

    Features

    siterwell describes Wireless Water Leak Alarm as having the following features:

    • Supported Notification Types
    • Battery Quantity
    • Battery powered using AA batteries
    • Color
    • FLiRS capable
    • Supports Network Wide Inclusion
    • Supports Z-Wave Explorer Frames
    • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

    Installation instructions

    Remove (Excluding) Sensor From Z-Wave Network
    1. Make sure the alarm is connected to power source.
    2. Set the Z-Wave Network controller into exclusion mode.
    3. Quickly, triple short the two sensing probes together by wet cloth, the LED light will flash for 3 times with beeping sound.
    4. Wait for the controller to remove (excluded) the alarm.
    Note: If the alarm is remove(excluded), then the sensor will be itself restored to factory default settings.

    Factory reset Wireless Water Leak Alarm

    Restore the Sensor to Factory Default Settings
    This operation will delete all information on Z-Wave network, and restore the factory default settings.
    1. Remove the battery, power off for a while. Now put on the battery.
    2. Wait for 5 seconds, When the LED is on, you should short the two sensing probes together with wet cloth within 5 seconds (before the LED turn off), and then remove the wet cloth quickly .
    3. Repeat the Step2 one times.
    4. The sensor will sound after successful operation, and it will last 2 seconds.
    Note: If this sensor is reset, the information of Z-Wave network in the sensor will be deleted. The sensor will be itself restored to factory default settings.Please use this procedure only when the network primary controller is missing or otherwise inoperable.

    Add (Including) Sensor To Z-Wave Network
    The water alarm can be included to the Z-wave network by following operations:
    1. Power on the alarm.
    2. Make sure the alarm is on its final install location, then set the controller into the inclusion mode.
    3. Quickly, triple short the two sensing probes together with wet cloth, the LED will flash alternately.
    4. The LED will flash 3 times with beeping after the alarm being Add (included) to the network successfully.

    Please note that this is a user manual Wireless Water Leak Alarm from Siterwell Technology is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Wireless Water Leak Alarm and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.