Smart Hub K2 (K2) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Smart Hub K2 (K2)from smanos. To view other Z-Wave products and manuals from smanos follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions


smanos Smart Hub K2
SKU Code
The smanos K2 gateway wirelessly connects to and controls all your Z-Wave sensors around the house so that they can send vital information or status reports to one another and to your K2 and ultimately your and your family’s smartphones. The smanos K2 is AC-powered, WiFi-based and has Z-Wave and RF modules built in, providing end users with endless possibilities to connect to a wide range of security sensors and smart home devices from smanos and beyond. In addition, the K2 has a backup, rechargeable battery, empowering you and your family with affordable, 24/7 protection and automation capabilities.
Version #
HW: 33 FW: 5.34:02.81 was the version certified
Certification #
Z-Wave Version


As a Z-Wave Plus certified product, Smart Hub K2 supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Access Control
  • S2 Authenticated
  • S2 Unauthenticated


smanos describes Smart Hub K2 as having the following features:

  • Sensors
  • Firmware updatable via a compatible Z-Wave gateway
  • Supported Notification Types
  • Battery Quantity
  • Thermostat Modes
  • Supported Meter Type
  • Communications Connections
  • Color
  • Communications Protocol
  • Switch Type
  • Thermostat HVAC Systems Supported
  • Battery powered using 18650 batteries
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

On the “smanos home” app, enter into the Accessories list from the Main Page, click on the room type [Location] where the device was installed. Tap on the device you want to exclude and slide from right to the left, then click on the [Trash Can] icon. Click on “YES” in the pop-up box, and the controller enters into Exclusion mode. Set the Z-Wave device into Learn mode according to its user manual.

After the controller is successfully connected to your home Wi-Fi network, on the “smanos home” app, enter into the Accessories list from the Main Page and find “Z-Wave Products”. Click/tap on “Z-Wave Products” and hit “START INCLUSION” to add the Z-Wave device of your choice.

Click on “Connect the K2 to Other Controller” in “Other Z-Wave Settings” section on the “smanos home” app, and the K2 enters into Learn mode. The K2 will terminate Learn mode if the connection is not established right away.
Note: The K2 must exclude other Z-Wave devices first, before it can be connected to another Z-Wave controller.

Factory reset Smart Hub K2

Note: If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.
In “Other Z-Wave Settings” section on the “smanos home” app, click on “Reset Z-Wave Module” and a pop-up box will be displayed. Click on “Reset” and the Z-Wave module inside the K2 will be restored to factory settings.

Please note that this is a user manual Smart Hub K2 from smanos is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. only warrants and is only able to support products purchased directly from us. If you have Smart Hub K2 and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.