The following is an overview of the user manual for the Z-Wave product Samsung Connect Home Pro (ET-WV531)from Samsung Electronics, Co., Ltd.. To view other Z-Wave products and manuals from SmartThings follow that link.
Overview
Security
As a Z-Wave Plus certified product, Samsung Connect Home Pro supports Z-Wave S2 security. The following security modes are directly supported:
Features
SmartThings describes Samsung Connect Home Pro as having the following features:
- Communications Connections
- Controller Supports Multiple Z-Wave Interfaces
- Firmware updatable via a compatible Z-Wave gateway
- Gateway Has Preferred Partners
- Sensors
- Supported Notification Types
- Controller Supports Multiple Networks
- Z-Wave Scene Type
- Color
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
Samsung SmartThings devices and many third-party devices that work with SmartThings require a connected SmartThings Hub (or compatible device with SmartThings Hub functionality).
You can connect these devices manually with the steps below.
1. Tap the plus icon in the bottom right
2. Tap Add Device Manually
3. Select the device category and brand OR enter your device's name in the search field
4. Follow the in-app instructions to perform the connection process specific to that device
5. The app will indicate when the device connects
6. Tap Edit to rename the device, and tap Done to save the name
7. Tap Done to complete the setup
Factory reset Samsung Connect Home Pro
1. Tap the menu
2. Tap the gear icon beside the Location with the Hub you wish to reset
3. Tap Remove Location
4. Confirm deletion by tapping Delete (IMPORTANT: deleting a Location cannot be undone)
NOTE: Resetting the Hub will restore factory settings. All device connections, automations, rules and configurations associated with that Hub will be lost in the reset. All devices connected to your Hub will have to be reset or excluded before they can be reconnected. The steps for resetting and reconnecting each smart device differ. After resetting, you can visit our Things category, find the devices you wish to set up, and follow the guides provided. Remember that you will likely need to reset or “exclude” every device before connecting.
There are two ways that devices can be deleted in the app.
This first method offers the option to delete multiple devices at once.
1. Tap My devices
2. Tap the three dots in the top right
3. Tap Delete devices
4. Select the device(s) to be deleted
5. Tap Delete
6. Tap Delete again to confirm
7. If only a Z-Wave device was selected, the app will prompt you to perform a Z-Wave exclusion on the device. Refer to the device's manual for specific exclusion steps
Note: If multiple devices are selected, any Z-Wave devices will need to be excluded manually
8. Tap Done
OR
The second method deletes devices on an individual basis.
1. Tap My devices and swipe to your Place
2. Tap the three dots in the top right
3. Tap Edit
4. Select the device to be deleted
5. Tap Delete device
6. Tap Delete again to confirm
7. For Z-Wave devices, the app will prompt you to perform a Z-Wave exclusion on the device. Refer to the device's manual for specific exclusion steps
8. Tap Done
Because the Hub is a certified Z-Wave device, you can add it to another Z-Wave network. Note that adding a Hub to a different Z-Wave network will disconnect it from any previously connected Z-Wave devices, and they will have to be put through the exclusion process before being added to the network again. SmartThings strongly discourages adding the Hub to another Z-Wave network. We cannot offer support for disconnected Z-Wave devices or the inability to add devices through the Hub as a result of including the Hub into another Z-Wave network.
Here are the steps to put the Hub into learn mode to receive network information from another Z-Wave controller:
1. Prepare the other Z-Wave controller to copy its network information to the Hub. This may be called include, add, transfer, copy, or replicate mode
2. In the SmartTings app,Tap the menu
3. Tap the Hub
4. Tap Z-Wave Utilities
5. Tap Include or Exclude Hub from an Existing Z-Wave Network
6. Tap OK
This will start learn mode on the Hub. It may take longer to receive all the network info and load all the devices. Check the other controller for confirmation of whether the transfer was successful.
Please note that this is a user manual Samsung Connect Home Pro from Samsung Electronics, Co., Ltd. is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Samsung Connect Home Pro and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.