The following is an overview of the user manual for the Z-Wave product Smart Home Hub (IM6001-V3P03)from Works as a SmartThings Hub. To view other Z-Wave products and manuals from SmartThings follow that link.
Overview
Security
As a Z-Wave Plus certified product, Smart Home Hub supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Access Control
- S2 Authenticated
- S2 Unauthenticated
Features
SmartThings describes Smart Home Hub as having the following features:
- Color
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
SmartStart location
SmartStart QR code's location as follows: 1. Guide product DSK location in manual: 5page
2. How to access product DSK :
SmartThings APP -> Dashboard -> Hub device card -> Hub detail information page
Product Classic Exclusion Description
Here are the steps to put the Hub into learn mode to receive network information from another Z-Wave controller:
Prepare the other Z-Wave controller to copy its network information to the Hub. This may be called include, add, transfer, shift, copy,
or replicate mode In the SmartThings Classic app, tap the menu (Android) / More (iOS) Tap the Hub Tap Z-Wave Utilities Tap Add
Hub to an existing Z-Wave network Tap OK This will start learn mode on the Hub. It may take longer to receive all the network info
and load all the devices. Check the other controller for confirmation of whether the transfer was successful.
Depending on the other controller, it may not have transferred the primary controller role to the SmartThings Hub,
and the Hub may not be able to add new devices.
To remove the Hub from the other network and reset it to default, follow the same steps above,
but put the other controller in remove or exclude mode instead.
Here are the steps to put the Hub into learn mode to receive network information from another Z-Wave controller:
Prepare the other Z-Wave controller to copy its network information to the Hub. This may be called include, add, transfer, shift, copy, or replicate mode
In the SmartThings Classic app, tap the menu (Android) / More (iOS)
Tap the Hub
Tap Z-Wave Utilities
Tap Add Hub to an existing Z-Wave network
Tap OK
This will start learn mode on the Hub. It may take longer to receive all the network info and load all the devices. Check the other controller for confirmation of whether the transfer was successful.
Depending on the other controller, it may not have transferred the primary controller role to the SmartThings Hub, and the Hub may not be able to add new devices. To remove the Hub from the other network and reset it to default, follow the same steps above, but put the other controller in remove or exclude mode instead.
use app invite another user through the app and then share your zwave device
Product Classic Inclusion Description
To connect a device: In the SmarThings app, follow these steps to connect or include a new device:
Tap My Home Under Things, tap Add a Thing at the bottom of your Things list The app will say Looking for device.
While the Hub searches, perform the connection/inclusion process specific to that device Consult the device's manual
for instructions When the device is discovered, it will be listed at the top of the screen Tap the device to rename it and
tap Done When finished, tap Save Tap Ok to confirm your added devices Alternatively, you can also explore and
connect third-party devices that work with SmartThings, or look for a specific device you want to connect:
Tap My Home Under Things, tap Add a Thing at the bottom of your Things list Tap Add device manually
Tap a device category (e.g., from Light Bulbs, Locks, Outlets, Thermostats, etc.) to see a list of related devices and
third-party devices that work with SmartThings Select your device Tap Connect Now The app will indicate that
it’s looking for the device While the Hub searches, perform the connection/inclusion process specific to that device
Consult the device's manual for instructions When the device is discovered, it will be listed at the top of the screen
Tap the device to rename it and tap Done Tap Done again Tap Save Tap Ok to confirm your added devices OR:
Tap Marketplace Under Things, tap a device category (e.g., from Light Bulbs, Locks, Outlets, Thermostats, etc.)
to see a list of related SmartThings devices and third-party devices that work with SmartThings Select your device
Tap Connect Now The app will indicate that it’s looking for the device While the Hub searches, perform
the connection/inclusion process specific to that device Consult the device's manual for instructions
When the device is discovered, it will be listed at the top of the screen Tap the device to rename it and tap Done
Tap Save Tap Ok to confirm your added devices If you’re having trouble connecting your device, it may need to be reset.
Consult the device’s manual for reset instructions or visit our Support Help Center for information about how to reset compatible devices.
Factory reset Smart Home Hub
Product Factory Reset
Wave factory reset To reset your Hub's Z-Wave system to factory default settings, you must factory reset the entire Hub.
You can factory reset your Hub with steps found below. NOTE: Resetting the Hub will restore factory settings.
All device connections, automations, rules, configurations, and SmartApps associated with that Hub will be lost in the reset.
All devices connected to your Hub will have to be reset or excluded before they can be reconnected. The steps for resetting
and reconnecting each smart device differ. After resetting, you can visit our Things category, find the devices you wish to set up,
and follow the guides provided. Remember that you will likely need to reset or “exclude” every device before connecting.
A physical factory reset is only possible for the Hub v2 with firmware 17.11 and up.
If you have a Hub v1 or a Hub with firmware below 17.11,
you can reset your Hub by deleting the Location it is connected to with these steps instead. Need to check your Hub’s firmware version?
Find out how here. Follow these instructions to reboot the Hub instead, without doing a full factory reset.
To factory reset the Hub: Make sure the Hub is plugged in with the included power and network cables
Press and hold the red recessed button on the back of the Hub for 30 seconds.
When the LED on the front switches from flashing yellow to solid yellow,
release the button Note: If you do not release the button within a few seconds after the LED switches to solid yellow,
the Hub may not begin the reset The Hub will take 10-15 minutes to fully factory reset.
Once the LEDs on the Hub turn solid green, you should then be able to connect your Hub again.
If you lost your original 6-character Welcome Code or are encountering other problems, these articles may help.
"If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and
it will be necessary after the reset to exclude and re-include all of the nodes in the network.
If this controller is being used as a secondary controller in the network,
use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable."
Please note that this is a user manual Smart Home Hub from Works as a SmartThings Hub is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Smart Home Hub and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.