The following is an overview of the user manual for the Z-Wave product Blind-curtain motor controller (SY-IOT101)from Somfy. To view other Z-Wave products and manuals from Somfy follow that link.
Overview
Security
As a Z-Wave Plus certified product, Blind-curtain motor controller supports Z-Wave S2 security. The following security modes are directly supported:
Features
Somfy describes Blind-curtain motor controller as having the following features:
- Color
- Communications Protocol
- Communications Connections
- Firmware updatable via a compatible Z-Wave gateway
- Window Covering Control Features
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
Factory reset Blind-curtain motor controller
Local Reset (Factory Default Reset )
- Press the program switch for above 10 second, then the LED is blinked until program switch is released.
- Release from the program switch.
- Then, SY-IOT101 module will try local reset.
- If local reset is succeeded, LED is blinked 5 times.
- After blinking LED, SY-IOT101 will send the “Device Reset Locally Notification” command and reset to the factory default.
- If local reset is failed, LED is turn off.
* Please use this procedure only when the network primary controller is missing or otherwise inoperable.
For “Manual Control Mode”
Press and hold Up Switch : UP
Press and hold Down Switch: Down
Release Up & Down Switch: Stop
For “Exclusion” removing from the network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to add the SY-IOT101 to your controller. To get in the “exclusion” mode.
- Check if SY-IOT101 module is in inclusion mode
- Press the program switch for above 5 second, then the LED is turned on.
- Release from the program switch.
- Then, SY-IOT101 module will try inclusion.
- If inclusion is succeeded, LED is blinked 3 times.
- If exclusion is failed, LED is turn off.
For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the SY-IOT101to your controller. To get in the “inclusion” mode.
- Check if SY-IOT101 module is in exclusion mode.
- Press the program switch for above 5 second, then, the LED is turned on.
- Release from the program switch.
- Then, SY-IOT101 module will try inclusion.
- If inclusion is succeeded, LED is blinked 3 times.
- If inclusion is failed, LED is turn off.
Device Learn Mode : This mode is for factory default or service mode (curtain or blind mode), not used by user.
* Entering this learn mode is some difficult, because this mode is only for factory or service mode.
- Put curtain or blind at close position first with remote or electrical switch.
- Press the program switch for 300(ms) and release it after 900(ms) as following.
. When press & release the program switch at first time, LED will be blink one time.
. When press & release the program switch at second time, LED will be blink two times.
. When press & release the program switch at third time, LED will be blink three times
- After LED blink three times, module will try device learn.
- Open the curtain or blind. Then, close the curtain or blind.
- This mode is to distinguish the device (curtain or blind) and measure the total distance between up and down in case of blind device.
Please note that this is a user manual Blind-curtain motor controller from Somfy is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Blind-curtain motor controller and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.