The following is an overview of the user manual for the Z-Wave product IS 140-2 Z-Wave (40111677001)from Steinel GmbH. To view other Z-Wave products and manuals from Steinel follow that link.
Overview
Smart home included.
The optional Smart Friends box and the free Smart Friends app make it easy to set the motion detector via smart phone or tablet. The light connected can also be switched ON or OFF via app. Other Steinel products can also be interconnected. If you wish, this also works via remote control when you are out. That completes your own light management system.
Along with STEINEL products, Smart Friends solutions from PAULMANN, SCHELLENBERG and ABUS can also integrated. Smart homes from a brand-name provider.
Security
As a Z-Wave Plus certified product, IS 140-2 Z-Wave supports Z-Wave S2 security. The following security modes are directly supported:
Features
Steinel describes IS 140-2 Z-Wave as having the following features:
- IP (Ingress Protection) Rated
- Firmware updatable via a compatible Z-Wave gateway
- Outdoor Use
- Neutral Wire Required
- Sensors
- Switch Load Capacity Volt-Ampere
- Switch Load Capacity Watts
- Supported Notification Types
- Electric Load Type
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
Inclusion = Add
To start the motion detector's inclusion mode, turn the device's control dial (E) to ""Set"" and back to ""0"" within 5 seconds.
Adding IS 140-2 to the Smart Friends system:
1) Download the Smart Friends app from the app store.
2) In the rooms view, activate the edit mode.
3) Select the chosen room and press the ""Add device"" button.
4) To put the device into inclusion mode, turn the device's control dial (E) to ""Set"" and back to ""0"" within 5 seconds. The status LED (F) lights up to show that this mode is selected.
5) The app displays a confirmation message once inclusion has been successfully completed.
Exclusion = Remove
To start the motion detector's exclusion mode, turn the device's control dial (E) to ""Set"" and back to ""0"" within 5 seconds.
Removing IS 140-2 from the Smart Friends system:
1) In the rooms view, activate the edit mode.
2) Select the device in the chosen room and press the ""delete"" button. Press delete and follow the instructions in the app.
3) To put the device into exclusion mode, turn the device's control dial (E) to ""Set"" and back to ""0"" within 5 seconds. The red status LED (F) lights up to show that this mode is selected.
4) The app displays a confirmation message once exclusion has been successfully completed.
Setting IS 140-2 with the app:
–– After programming, an ON/OFF scene is automatically created in the app.
–– The following setting values are then automatically stored:
a) Twilight setting = control-dial setting
b) Time setting = 3 min switch-OFF delay
–– The twilight and time settings can be selected to the accuracy of one lux and one second respectively in the ""Scene"" menu.
Factory reset IS 140-2 Z-Wave
Resetting IS 140-2 to factory settings:
Please use this procedure only when the network primary controller is missing or otherwise inoperable.
1) Turn the device's control dial (E) to ""Set"" and move it to ""Reset"" within 5 seconds.
2) The status LED (F) briefly flashes to show that the light has been reset.
3) The device is now no longer included in the Z-Wave system and has been returned to factory settings.
Please note that this is a user manual IS 140-2 Z-Wave from Steinel GmbH is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have IS 140-2 Z-Wave and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.