RS LED D2 Z-Wave (6772) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product RS LED D2 Z-Wave (6772)from Steinel GmbH. To view other Z-Wave products and manuals from Steinel follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions


RS LED D2 Z-Wave
SKU Code
Sleek, attractive lines. Opting for the RS LED D2 designer indoor luminaire, you'll be giving your home a real designer highlight with pleasant LED illumination. With its stunning looks and intelligent technology, this light provides the last word in stylish home convenience. Once fitted to the wall or ceiling, the high-frequency sensor switches it 'ON' and 'OFF' in complete silence and all automatically. The light is child's play to install and the function settings on the product are easy to understand too. Your neighbours will be amazed.

Smart home included.
The optional Smart Friends Box and the free Smart Friends app make it easy to set the RS PRO LED D2 Z-Wave via smart phone or tablet. The light can also be switched ON or OFF via app. Other Steinel products can also be interconnected. If you wish, this also works via remote control when you are out. That completes your own light management system.
Along with STEINEL products, Smart Friends solutions from PAULMANN, SCHELLENBERG and ABUS can also integrated. Smart homes from a brand-name provider.
Version #
HW: 1 FW: 1.00:01.00 was the version certified
Certification #
Z-Wave Version


As a Z-Wave Plus certified product, RS LED D2 Z-Wave supports Z-Wave S2 security. The following security modes are directly supported:


    Steinel describes RS LED D2 Z-Wave as having the following features:

    • Supported Notification Types
    • Switch Load Capacity Watts
    • Sensors
    • Switch Load Capacity Current
    • Switch Load Capacity Volt-Ampere
    • Z-Wave Scene Type
    • Firmware updatable via a compatible Z-Wave gateway
    • Outdoor Use
    • Neutral Wire Required
    • Electric Load Type
    • Color
    • FLiRS capable
    • Supports Network Wide Inclusion
    • Supports Z-Wave Explorer Frames
    • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

    Installation instructions

    Inclusion: Add

    Adding RS LED D2 to the Smart Friends system:
    1 Download Smart Friends app from the app store.
    2 In the rooms view, activate the edit mode.
    3 Select the chosen room and press the ""Add device"" button.
    4 Briefly press button 5 on the device to set it to inclusion mode. Status LED 8 lights up to show that this mode is selected.
    5 The app displays a confirmation message once inclusion has been successfully completed.

    Setting RS LED D2 via the app
    –– After programming, an ON/OFF scene is automatically created in the app.
    –– The following setting values are then automatically stored:
    a) Twilight setting = control-dial setting
    b) Time setting = 3-minute switch-off delay
    –– The twilight and time settings can be selected to the accuracy of one lux / second in the ""Scene"" menu.

    Factory reset RS LED D2 Z-Wave

    Returning RS LED D2 to factory settings:
    Please use this procedure only when the network primary controller is missing or otherwise inoperable.
    1 Briefly press button e and directly afterwards keep it pressed for 5 seconds.
    2 Status LED h briefly flashes to show that the light has been reset.
    3 The device is now no longer included in the Z-Wave system and has been returned to factory settings.

    Exclusion: Remove

    Removing RS LED D2 from the Smart Friends system:
    1 In the rooms view, activate the edit mode.
    2. Select the device in the chosen room and press the ""delete"" button. Press delete and follow the instructions in the app.
    3 Briefly press button e on the device to set it to exclusion mode. The red status LED h lights up to show that this mode is selected.
    4 The app displays a confirmation message once exclusion has been successfully completed.

    Please note that this is a user manual RS LED D2 Z-Wave from Steinel GmbH is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. only warrants and is only able to support products purchased directly from us. If you have RS LED D2 Z-Wave and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.