Toastcam (V3 / NE350) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Toastcam (V3 / NE350)from TOASTCAM. To view other Z-Wave products and manuals from TOASTCAM follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
TOASTCAM
SKU Code
V3 / NE350
Description
ToastCAM is a cloud-based digital network camera. It is equipped with a wide range of functions including alarm monitoring, motion detection, night vision, recording and replay of video and audio.
It is also an intelligent gateway controller, it includes a Z-Wave Controller so integrates the other wireless wireless devices and sensors. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
Version #
HW: 1 FW: 5.14:02.61:01.00:01.00 was the version certified
Certification #
ZC10-18025993
Certified
2018-01-12T19:10:07.799766
Z-Wave Version
6.81.00

Security

As a Z-Wave Plus certified product, Toastcam supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Access Control
  • S2 Authenticated
  • S2 Unauthenticated

Features

TOASTCAM describes Toastcam as having the following features:

  • Color
  • Communications Protocol
  • Sensors
  • Supported Notification Types
  • Communications Connections
  • Controller Supports Multiple Networks
  • Firmware updatable via a compatible Z-Wave gateway
  • IP (Ingress Protection) Rated
  • Outdoor Use
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

Pressing the ""ADD NEW DEVICE"" button will let camera into inclusion mode 30 seconds. User can now trigger the device's node information frame to add to the camera's z-wave network.
With Z-Wave Security 2, user needs to accept or modify the security class settings. It is recommended that the user not change the security class settings.
Additionally for Security 2 Class 1 and 2 devices, the user needs to key in the 1st 5 digits of the DSK.

Pressing the ""REMOVE DEVICE button will let camera into exclusion mode 30 seconds. User can now trigger the device's node information frame to remove device from any z-wave network.

Factory reset Toastcam

This is the Z-Wave Set Default network operation and it pops up a confirmation prompt. If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the
network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.

This performs the Z-Wave Set Learn Mode network operation. This can only be performed when Z-Ware is not in a network and will typically make Z-Ware an Inclusion or Secondary Controller, in which case, some of its facilities will not be available. To complete an S2 inclusion, the DSK may need to be entered on the including Controller.
Note that this function may let camera works as ""secondary controller"" or ""inclusion controller"" in another existing network, just start inclusion mode or controller shift on another controller, then start camera learn mode, after inclusion, camera will replicate node information from another controller.
Since our design is based on ""primary controller"", we recommend that you just use our camera as ""primary controller"".

Please note that this is a user manual Toastcam from TOASTCAM is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Toastcam and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.