The following is an overview of the user manual for the Z-Wave product ISY-994 Series (ISY-994ZW)from Universal Devices. To view other Z-Wave products and manuals from Universal Devices follow that link.
Overview
Security
As a Z-Wave Plus certified product, ISY-994 Series supports Z-Wave S2 security. The following security modes are directly supported:
Features
Universal Devices describes ISY-994 Series as having the following features:
- Communications Connections
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
1. Select Z-Wave | Add a Z-Wave Device and wait for a popup window to appear.
- If the popup window does not appear, Select Z-Wave | Advanced | Stop Adding or Removing a Z-Wave Device then try again.
2. Put the other controller into Learn Mode. Refer to the user guide for your product on how to do this.
3. The ISY will begin updating the other controller
Set Z-Wave | Options | Use Network Wide Search when adding or removing Z-Wave devices (NWI/NWE) to enable or disable NWI/NWE when adding or removing devices.
1. Select Z-Wave | Add a Z-Wave Device and wait for a popup window to appear.
- If the popup window does not appear, Select Z-Wave | Advanced | Stop Adding or Removing a Z-Wave Device then try again.
2. Put the Z-Wave device you are adding into learn Mode. Refer to the user guide for your product on how to do this. In many cases this just requires you to press a button on the device.
3. The ISY will begin adding the device (this may occur a few seconds after you put the device into learn mode).
- The popup window will go away and you will see your device added to the tree.
Note: To add a device, it must not already be in a Z-Wave network. Therefore, if you are having trouble adding a device try removing it first.
1. Select Z-Wave | Remove a Z-Wave Device and wait for a popup window to appear.
- If the popup window does not appear, Select Z-Wave | Advanced | Stop Adding or Removing a Z-Wave Device then try again.
2. Put the Z-Wave device into learn Mode. Refer to the user guide for your product on how to do this. In many cases this just requires you to press a button on the device.
3. The ISY will remove the device (this may occur a few seconds after you put the device intolearn mode).
- The popup window will go away and the nodes for the device will be removed from the tree.
1. Select Z-Wave | Learn Mode and wait for a popup window to appear.
- If the popup window does not appear, Select Z-Wave | Advanced | Stop Adding or Removing a Z-Wave Device then try again.
2. The ISY will now wait to receive information from another Z-Wave device performing an action such as Add, Remove, etc.
- The popup window will go away when the operation is complete.
- In some cases this may take 30 to 60 seconds or longer to complete.
Note: Learn Mode is only available if the Z-Wave network is empty or the ISY is not the SIS for the Z-Wave network.
Factory reset ISY-994 Series
When the Z-Wave dongle in the ISY is factory reset it is also given a new Home Id and new S0 security keys are generated.
To factory reset the Z-Wave dongle, select Z-Wave | Advanced | Factory Reset Z-Wave Dongle
If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.
Please note that this is a user manual ISY-994 Series from Universal Devices is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have ISY-994 Series and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.