The following is an overview of the user manual for the Z-Wave product Heat Controller (FGT-001)from Venture WISE. To view other Z-Wave products and manuals from Venture WISE follow that link.
Overview
automatically adjusts the heat level.
It can be mounted without tools on three types of thermostatic
radiator valves.
You can create schedules via an app to easily manage temperature
throughout the week.
Main features of the Device:
- to be installed on three types of valves: M30 x 1.5, Danfoss RTD-N
and Danfoss RA-N,
- compatible with any certified Z-Wave™ Controller,
- supports Z-Wave™ network Security Modes: S0 with AES-128
encryption and S2 with PRNG-based encryption,
- built-in battery recharged through standard micro-USB port,
- easy installation - no tools required,
- can use a dedicated temperature sensor,
- supports heating schedules,
- automatic calibration,
- anti-freeze function,
- descaling function,
- unconstrained rotation spherical knob to set the desired temperature.
Security
As a Z-Wave Plus certified product, Heat Controller supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
Venture WISE describes Heat Controller as having the following features:
- Firmware updatable via a compatible Z-Wave gateway
- Thermostat HVAC Systems Supported
- Thermostat Modes
- Thermostat Power Source
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
SmartStart location
SmartStart QR code's location as follows: If you are adding in S2 authenticated mode, type in the device pin
code (underlined part of the public key on the label).
Adding (Inclusion) - Z-Wave device learning mode, allowing to add
the device to existing Z-Wave network.
To add the device to the Z-Wave network:
1. Make sure the device is within the direct range of your Z-Wave
controller.
2. Set the main controller in (security/non-security) add mode (see
the controller’s manual)
3. Quickly triple click the button on the thermostatic head (A) or use
the included key (B).
4. The LED ring will start blinking white.
5. If you are adding in S2 authenticated mode, type in the device pin
code (underlined part of the public key on the label).
6. Wait for the adding process to end.
7. Successful adding will be confirmed by the Z-Wave controller and
green LED colour.
Removing (Exclusion) - Z-Wave device learning mode, allowing to
remove the device from existing Z-Wave network.
To remove the device from the Z-Wave network:
1. Make sure the device is within the direct range of your Z-Wave
controller.
2. Set the main controller into remove mode (see the controller’s
manual).
3. Quickly triple click the button on the thermostatic head (A) or use
the included key (B).
4. The LED ring will start blinking white.
5. Wait for the removing process to end.
6. Successful removing will be confirmed by the Z-Wave controller
and red LED colour.
NOTE: The product manual doesn't contain the following information.
This device is a Z-Wave FLiRS device, so it doesn't need to be woken up by the user.
Factory reset Heat Controller
Reset procedure allows to restore the device back to its factory settings,
which means all information about the network and user configuration
will be deleted.
To perform factory reset:
1. Press and hold the button (A) or use the included key (B).
2. Release the button when you see yellow LED colour.
3. Click the button to confirm the selection.
4. After finishing resetting the device will be put in Standby Mode.
Click the button to activate it again.
Please note that this is a user manual Heat Controller from Venture WISE is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Heat Controller and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.