4 in 1 PIR Sensor (ZP3113US-7) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product 4 in 1 PIR Sensor (ZP3113US-7)from Vision. To view other Z-Wave products and manuals from Vision follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions


4 in 1 PIR Sensor
SKU Code
* Includes Motion, Temperature, Humidity, and Light sensor
* 360-degree detection (suitable for ceiling fixture)
* Compact Size: 59*59*41mm
* 1 x CR123Battery
* Low Battery Detection
* LED Status Indicator
* 100feet line of sight
Version #
HW: 1 FW: 32.32 was the version certified
Certification #
Z-Wave Version


As a Z-Wave Plus certified product, 4 in 1 PIR Sensor supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Authenticated
  • S2 Unauthenticated


Vision describes 4 in 1 PIR Sensor as having the following features:

  • Battery powered using CR123A batteries
  • Firmware updatable via a compatible Z-Wave gateway
  • Battery Quantity
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

User doesn't need to trigger capability rediscovery on their controller.

Parameter1: Choose Temperature Unit (C or F)
Parameter2: Temperature changed interval for the notification report.
Parameter3: Humidity changed interval for the notification report.
Parameter4: Lightness changed interval for the notification report.
Parameter5: PIR retriggering interval for power saving.
Parameter6: PIR Sensitivity
Parameter7: LED Mode Selection for power saving.
Parameter8: PIR Trigger Notification Re-sending Times

For “Inclusion” in (adding to) a network: To add the ZP3113 to your Z-Wave network (inclusion), place your Z-Wave primary controller into inclusion mode. Press the Program Switch of ZP3113 once for sending the NIF. After sending NIF, Z-Wave will send the auto inclusion, otherwise, ZP3113 will go to sleep after 30 seconds. The LED indicator will be flashing while the inclusion is continued.

For “Exclusion” from (removing from) a network: To remove the ZP3113 from your Z-Wave network (exclusion), place your Z-Wave primary controller into “exclusion” mode, and following its instruction to delete the ZP3113 to your controller. Press the Program Switch of ZP3113 once to be excluded.

Wake Up Notification:
Press “Program SW” once to send NIF and LED will flash once, it takes around 10 seconds to send “Wake Up Notification” for receiving all command classes or go to sleep mode after 10 seconds without receiving any command.

Factory reset 4 in 1 PIR Sensor

Factory Default Reset:
Remove cover to trigged tamper switch, LED flash once & send out Alarm Report. Press Program Switch 10 times within 10 seconds, ZP3113 will send the “Device Reset Locally Notification” command and reset to the factory default. (Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.)

SmartStart location

SmartStart QR code's location as follows: (1) The DSK label is on the backside of ZP3113-7
(2) Scan the DSK label to access the SmartStart if gateway 's UI supports SmartStart

Please note that this is a user manual 4 in 1 PIR Sensor from Vision is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have 4 in 1 PIR Sensor and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.