Mini Gateway (ZA1021US-7) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Mini Gateway (ZA1021US-7)from Vision. To view other Z-Wave products and manuals from Vision follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions


Mini Gateway
SKU Code
This gateway designed to manage your intelligent home and may control up to 230 devices via the wireless Z-Wave™ communication protocol. This Hub connects all of the different Z-Wave sensors around your home so that you can receive notifications by smartphone even you are away from home.
Version #
HW: 1 FW: 7.15:07.15 was the version certified
Certification #
Z-Wave Version


As a Z-Wave Plus certified product, Mini Gateway supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Access Control
  • S2 Authenticated
  • S2 Unauthenticated


Vision describes Mini Gateway as having the following features:

  • Communications Connections
  • Communications Protocol
  • Firmware updatable via a compatible Z-Wave gateway
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

1) Follow the manufacturer’s instructions of the other controller to enable it into Add mode.
2) Click “Learn Mode” button. If it is a S2 Controller, the DSK of the Gateway will appear. Please key in the DSK to the other Controller UI when prompted.
3) When completed, the UI will show the existing Controller and device(s) in the network.

Factory reset Mini Gateway

Step 1: Click Gateway setting button.
Step 2: Select “Z-Wave Reset” button.
Step 3: Confirm the dialog. Click “Reset” button will perform a factory reset to the Gateway.

SmartStart location

SmartStart QR code's location as follows: page 23

SmartStart installation

Step 1: Click “SmartStart” from Z-Wave menu.
Step 2: Type in 40 decimals S2 DSK number of the device which user wants to add in using SmartStart and presses “Send”.

Step 1: Click button “Add Device” on the website.
Step 2: System is on inclusion mode and waiting for user to trigger inclusion mode of device.
Step 3: After triggering device, the gateway will show “Setting Security Grant”. If the device supports S2 Security, please choose the security level for the device. If the selection is “S2 Access Control” or “S2 Authenticated”, the system will prompt user to input the device first 5 digit of the DSK.
If device only supports S0, the gateway will automatically skip “Setting Security Grant” step.
Step 4: Wait for the whole inclusion process to finish; it may take up to 1-2 minutes depending on the device.
Step 5: If the inclusion is successful, the system will show “device included successfully”. Otherwise, a failure message will appear.
Step 6: If the inclusion is successful, you will be asked to name the device and set up a location of the device.

Step 1: Click button “Remove Device”.
Step 2: System is on exclusion mode and waiting for user to trigger the intended device to removal mode.
Step 3: If the exclusion is successful, system will show the excluded node ID on the pop-up window.

1) Start the add device process in Adding Device.
2) Follow the manufacturer’s instructions of the other controller to enable it to go into learn mode.
3) Enter DSK code if necessary, and await the whole process to finish.

You can use “Remove” button to remove the specified DSK.

Step 1: Click “Request” button, the Mini Gateway would rediscovery the device capability.
Step 2: If successful, the device information would update correctly.

Please note that this is a user manual Mini Gateway from Vision is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. only warrants and is only able to support products purchased directly from us. If you have Mini Gateway and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.