Categories

Aeotec

Atrim

SmartThings

Z-Wave Products

nexTouch Sectional Mortise Touch Screen Keypad Lock (NTM622-ZW2) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product nexTouch Sectional Mortise Touch Screen Keypad Lock (NTM622-ZW2)from Yale Locks & Hardware. To view other Z-Wave products and manuals from Yale follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions

Overview

Name
nexTouch Sectional Mortise Touch Screen Keypad Lock
SKU Code
NTM622-ZW2
Description
Expanding the Yale nexTouch™ product line for even more applications, the new nexTouch Sectional Mortise Keypad Lock provides robust security for a wide range of commercial and multi-family buildings. Just like the original cylindrical nexTouch lock, it is ANSI/BHMA Grade 1 certified and offered in capacitive touchscreen or pushbutton keypad versions. With just the addition of a Z-Wave Plus™ module, you can add this lock to compatible smart home and alarm systems. Other standard features include voice-guided programming, privacy mode with Door Position Switch, 9V battery backup, support of up to 100 unique user codes, and more.
Version #
HW: 255 FW: 1.78:32.27 was the version certified
Certification #
ZC10-22067096
Certified
2022-06-03T11:07:04.676294
Z-Wave Version
6.51.07

Security

As a Z-Wave Plus certified product, nexTouch Sectional Mortise Touch Screen Keypad Lock supports Z-Wave S2 security. The following security modes are directly supported:

    Features

    Yale describes nexTouch Sectional Mortise Touch Screen Keypad Lock as having the following features:

    • Battery Quantity
    • Battery powered using batteries
    • Door Lock Type
    • Firmware updatable via a compatible Z-Wave gateway
    • IP (Ingress Protection) Rated
    • Outdoor Use
    • Supported Notification Types
    • FLiRS capable
    • Supports Network Wide Inclusion
    • Supports Z-Wave Explorer Frames
    • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

    Installation instructions

    1. Enter the 4-8 digit master PIN code followed by the gear key.
    2. Press the 7 key followed by the gear key.
    3. Press the 1 key followed by the gear key.

    1. Enter the 4-8 digit master PIN code followed by the gear key.
    2. Press the 7 key followed by the gear key.
    3. Press the 3 key followed by the gear key.

    Touch the touchscreen with three fingers

    Factory reset nexTouch Sectional Mortise Touch Screen Keypad Lock

    Please use this procedure only when the network primary controller is missing or otherwise inoperable.
    1. Remove the inside lever with the lever removal tool.
    2. Remove battery cover using hex wrench provided with lock.
    3. Remove four (4) AA batteries.
    4. Remove the 10-32 x 3/4"" pan head screw from the center of the battery housing into the barrel nut of the outside assembly.
    5. Remove inside escutcheon. Cables may stay connected.
    6. Reinstall batteries
    7. On the back of the PC board, push and hold the Reset Button with the lever removal tool for 3 seconds.
    8. While continuing the press the reset button, temporarily remove one AA battery.
    9. Reinstall the battery
    10. Release reset button and wait 15 seconds. Speaker will announce ""Welcome to Yale""
    11. Reassemble escutcheon

    Please note that this is a user manual nexTouch Sectional Mortise Touch Screen Keypad Lock from Yale Locks & Hardware is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have nexTouch Sectional Mortise Touch Screen Keypad Lock and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.