The following is an overview of the user manual for the Z-Wave product Siren alarm EU (ne-nas-ab02z.eu)from Zipato. To view other Z-Wave products and manuals from Zipato follow that link.
Overview
· Set the siren and warning light to turn on when unexpected activity is detected.
· Set up the siren so that it’s triggered automatically by your sensors and camera. Get smart alerts when doors or windows are opened unexpectedly or when motion is detected.
Security
As a Z-Wave Plus certified product, Siren alarm EU supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Unauthenticated
Features
Zipato describes Siren alarm EU as having the following features:
- Supported Notification Types
- Battery Quantity
- Battery powered using CR123A batteries
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
Factory reset Siren alarm EU
Reset procedure will remove all information on the Z-Wave network or Z-Wave controller and restore the sensor to factory default settings. Please use this procedure only when the network primary controller is missing or otherwise inoperable.
1) Remove the sensor’s cover
2) Make sure the sensor is connected to power source
3) Press the code button for 10 seconds, LED will flash blue for 3 seconds
4) Release the code button
Note:
When the siren is being restored to factory settings, please make sure power source is connected.
1. Configure alarm volume
This parameter defines the output volume when siren plays alarm. Doorbell alarm volume has three settings, Low (Parameter is set to ‘1’), Middle (Parameter is set to ‘2’), High (Parameter is set to ‘3’). The default value is ‘2’.
2. Configure alarm duration time
This Parameter defines the alarm duration time when siren receives an alarm sensor notification report or an alarm command from controller. Siren duration time has three settings: 30 seconds (Parameter is set to ‘1’), 1 minute (Parameter is set to ‘2’), 5 minute (Parameter is set to ‘3’). The default value is ‘2’.
3. Configuring doorbell music duration time
This parameter defines the doorbell music duration time when siren receives a door/window sensor notification report or an alarm command (BASIC_SET =0x02) from a controller. The doorbell music will be played always if this parameter is set to ‘0’. The doorbell music will not be played if this parameter is set to ‘255’. Other values are the doorbell music playing duration time. Unit: Time.
4. Configure doorbell music volume
This parameter defines the output volume when siren plays doorbell music. Doorbell music volume has three settings: Low (Parameter is set to ‘1’), Middle (Parameter is set to ‘2’), High (Parameter is set to‘3’). The default value is ‘2’.
5. Configure alarm sound index
This parameter defines the alarm sound index so siren can play different sound when an alarm occurs. There are 10 different sounds for user selection.
6. Configure doorbell music index
This parameter defines the doorbell music index so siren can play different music when an alarm occurs. There are 10 different music compositions for user selection.
Note The alarm sounds are very loud and can damage your hearing. During acoustic alarm, please keep sufficient distance to the siren and protect your hearing.
Battery check command
Users can also inquire the battery status of the siren by sending BATTERY_GET command. Once the siren receives the command, it will return BATTERY_ REPORT command. The siren will send BATTERY_ LEVEL=0xFF command to the Z-Wave Controller to inform that the siren is in dead battery status, otherwise BATTERY_LEVEL value range is 0% to 100%.
Command Classes
This Sensor supports Command Classes as Below:
* COMMAND_CLASS_ZWAVEPLUS_INFO (V2)
* COMMAND_CLASS_VERSION (V2)
* COMMAND_CLASS_MANUFACTURER_SPECIFIC (V2) * COMMAND_CLASS_DEVICE_RESET_LOCALLY (V1) * COMMAND_CLASS_POWERLEVEL (V1)
* COMMAND_CLASS_BATTERY (V1)
* COMMAND_CLASS_ASSOCIATION (V2)
* COMMAND_CLASS_ASSOCIATION_GRP_INFO (V1) * COMMAND_CLASS_WAKE_UP (V2)
* COMMAND_CLASS_SWITCH_BINARY (V1)
* COMMAND_CLASS_NOTIFICATION (V4)
* COMMAND_CLASS_CONFIGURATION (V1)
The indoor siren can be included to the Z-Wave network by pressing the code button.
1) Disassemble the siren and insert the battery into
the siren. Make sure the device is located within
the direct range of the controller.
2) Set the controller into the inclusion mode (see
main controller’s operating manual).
3) Quickly triple click the code button, LED light will
flash red for 5 times.
4) The Indoor siren will be detected and included
in the Z-Wave network.
5) Wait for the main controller to configure the siren.
SMART START. This product also supports Z-Wave Smart Start option which enables easier inclusion. QR code for SmartStart inclusion is printed on the battery cover. SmartStart option is only possible when network controller is also supporting SmartStart.
1) Make sure the siren is connected to power source. 2) Set the main controller into the exclusion mode
(see main controller’s operating manual).
3) Quickly triple click the code button, LED light
will flash red for 5 times
4) Wait for the main controller to remove the sensor.
Please note that this is a user manual Siren alarm EU from Zipato is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Siren alarm EU and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.