The following is an overview of the user manual for the Z-Wave product Nano Shutter (ZW141-C)from Aeotec. To view other Z-Wave products and manuals from Aeotec follow that link.
Overview
1. Used to control the motor of Curtain, support Shutter Mode and Venetian Mode .
2. Can be calibrated according to diff e rent curtains
3. Used to control other Z-Wave device directly.
4. Support S2, more safe and more re liable
5. Support SmartStart, faster inclusion
Security
As a Z-Wave Plus certified product, Nano Shutter supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
Aeotec describes Nano Shutter as having the following features:
- Color
- Firmware updatable via a compatible Z-Wave gateway
- Neutral Wire Required
- Switch Load Capacity Current
- Window Covering Control Features
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
3.6 How to Remove the device from Z-Wave network
1. Set your Z-Wave Controller into its 'Remove Device' mode in order to remove the product from your Z-Wave system. Refer to the Controller's manual if you are unsure of how to perform this step.
2. Click Action Button/S1/S2(external switch need to be identified first) 6 times will enter exclusion mode.
3. If Removing fails, it will bright red light for 2s then turn back to Regular Light Mode, repeat steps 1-2. Contact us for further support if needed.
4. If Removing succeeds, it will alternate through a rainbow of colors. Now, it is removed from Z-Wave network successfully.
Calibration for Shutter have 2 modes: Shutter Mode for Standard roller blind, and Venetian Mode for Venetian Blind. Shutter will record the Curtain Trip Time for Shutter mode and Curtain Trip Time + Blade Turn Time for Venetain Mode.
The detail can be found in section 4.2 Calibration in Advanced information Product Manual.
SmartStart location
SmartStart QR code's location as follows: There is no DSK on the product.QR code used for SmartStart inclusion. DSK code can be found on packaging.
Factory reset Nano Shutter
3.7 How to Factory Reset
Manually, press and hold the Action Button for at least 20s and then release. The LED indicator will alternate through a rainbow of colors, which indicates the reset operation is successful. Otherwise, please try again. Contact us for further support if needed.
Note:
1. This procedure should only be used when the primary controller is missing or inoperable.
2. Factory Reset will:
a) Remove the product from Z-Wave network;
b) Delete the Association setting;
3.5.2 Classic inclusion Learn Mode
1. Set your Z-Wave Controller into its 'Add Device' mode in order to add the product into your Z-Wave system. Refer to the Controller's manual if you are unsure of how to perform this step.
2. Make sure the product is powered. After powered up, Its LED will alternate through a rainbow of colors all the time.
3. Click Action Button once, it will quickly flash blue light for 30 seconds until it is added into the network.
4. If your Z-Wave Controller supports S2 encryption, enter the first 5 digits of DSK into your Controller's interface if /when requested. The DSK is printed on its housing.
5. If Adding fails, it will bright red light for 2s and then alternate through a rainbow of colors; repeat steps 1 to 4. Contact us for further support if needed.
6. If Adding succeeds, it will bright blue light for 2s and then turn to Motor Mode(green for runing, off for stop). Now, this product is a part of your Z-Wave home control system. You can configure it and its automations via your Z-Wave system; please refer to your software's user guide for precise instructions.
Please note that this is a user manual Nano Shutter from Aeotec is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Nano Shutter and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.