The following is an overview of the user manual for the Z-Wave product Smart Boost Timer Switch (ZWA006-C)from Aeotec. To view other Z-Wave products and manuals from Aeotec follow that link.
Overview
The Aeotec Smart Boost Time Switch supports consumption meter function. When the device has been included in the network, it will report the consumption power periodically. It is also a high output countdown timer that can be used to control immersion heater elements or other electrical appliances rated up to 16A. On the product, four simple white LEDs are used to show the user how much time is left to run. Pressing the switch whilst the unit is operating allows the user to cancel the timing program,and the memory function of the timer will remember the last period selected.
Security
As a Z-Wave Plus certified product, Smart Boost Timer Switch supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
Aeotec describes Smart Boost Timer Switch as having the following features:
- Switch Type
- Switch Load Capacity Current
- Supported Meter Type
- Firmware updatable via a compatible Z-Wave gateway
- Switch Load Capacity Volt-Ampere
- Battery Quantity
- Battery powered using CR2032 batteries
- Color
- Sensors
- Switch Load Capacity Watts
- Electric Load Type
- Neutral Wire Required
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
1. Power on the device, and the power led will blink blue slowly.
2. Put the Z-Wave Primary Controller into inclusion mode (If you don’t know how to do this, refer to its manual)
3. Press and hold the action button, and when the yellow LED is on, release the button. It indicates the device has enter learn mode.
4. If added successfully, the power LED will remain green for 2 seconds, then turn off.
1. Power on the device.
2. Put the Primary Controller into exclusion mode (If you don’t know how to do this refer to its manual)
3. Press and hold the action button, and when the purple LED turns on, release the button. This indicates that the device has entered learn mode. If removal is successful, the blue LED will blink slowly.
Factory reset Smart Boost Timer Switch
Please use this procedure only when the primary controller is missing or inoperable.
1. Make sure the device has been powered.
2. Press and hold the action button for 15 seconds. When the red LED turns on, release the button. Then, the device will enter factory reset mode. If the reset is successful, the LED will blink blue slowly.
Boost Mode
1. Power on the device.
a) Press and hold the button about 1 second, when the power LED turns white, release the button. Then the 1st boost time LED will turn on. This indicates that the device entered boost mode. The switch will turn on immediately and will turn off after 30 minutes (This time can be changed through Configuration Parameter 5).
b) Press and hold the button about 1 second after doing a), when the power LED turns white, release the button. The 1st and 2nd boost time LEDs will turn on, which means the switch will turn off after 60 minutes.
c) Press and hold the button about 1 second after doing b), when the power LED turns white release the button. The 1st, 2nd and 3rd boost time LEDs will turn on, which means the switch will turn off after 90 minutes.
d) Press and hold the button about 1 second after doing c), when the power LED turns white release the button. The 1st, 2nd, 3rd, and 4th boost time LEDs will turn on, which means the switch will turn off after 120 minutes.
e) Press and hold the button about 1 second after doing d), when the power LED turn off release the button. Then all of the boost time leds will turn off, which indicates that boost mode has been exited.
2. Press and hold the button about 5 seconds.
a) When the power LED turns green, release the button, and the device will enter an override schedule state. At this state, the schedule task doesn’t work. The switch can only be turned on or off from the gateway.
b) When the power LED turns red, release the button, and the device will exit the override schedule state.
Please note that this is a user manual Smart Boost Timer Switch from Aeotec is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Smart Boost Timer Switch and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.