The following is an overview of the user manual for the Z-Wave product Range Extender (4AR1S70EN0)from Ring. To view other Z-Wave products and manuals from Ring follow that link.
Overview
The Ring Extender is a Z-Wave range extender with battery backup. It is a Security Enabled Z-Wave Plus Product and requires a security-enabled Z-Wave Plus controller to make use of all of its features. It will repeat Z-Wave commands from all nodes in the network, from any certified Z-Wave device manufacturer. Any non-battery powered Z-Wave device will also repeat signals in a Z-Wave network.
Security
As a Z-Wave Plus certified product, Range Extender supports Z-Wave S2 security. The following security modes are directly supported:
- S2 Authenticated
- S2 Unauthenticated
Features
Ring describes Range Extender as having the following features:
- Color
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
SmartStart location
SmartStart QR code's location as follows: The QR Code and DSK label is shown on the outside packaging of the box. The full DSK string is also located in the leaflet inside the packaging. The same DSK is printed in the form of a QR code on the back of the device as well.
Classic Inclusion (Add to System) - S2
1. For proper inclusion, bring the Range Extender to the final location where it will be used*.
2. Follow the instructions provided in Ring Alarm Mobile Application, enter DSK pin to enter inclusion mode.
3. Supply power to the Range Extender and then press the button once to begin inclusion mode using S2 encryption.
4. The device will enter inclusion mode indefinitely and the LED Indicator will blink slowly (1 flash/2 sec) until it’s included in a system.
5. Upon successful inclusion, the LED Indicator will stop blinking.
*For non Z-Wave Plus networks, please consult the owner’s manual for your primary controller to determine the best method and location for adding the Range Extender to your Z-Wave network.
SmartStart Inclusion (Add to System) - SmartStart
1. For proper inclusion, bring the Range Extender to the final location where it will be used*.
2. Follow the instructions provided in Ring Alarm Mobile Application, scan QR code to enter inclusion mode.
3. Supply power to the Range Extender to begin Smart Start (inclusion) mode.
4. The device will enter inclusion mode indefinitely and the LED Indicator will blink slowly (1 flash/2 sec) until it’s included in a system.
5. Upon successful inclusion, the LED Indicator will stop blinking.
Exclusion (Remove from System)
1. Make sure the Range Extender is powered on.
2. Follow the instructions in Ring Alarm Mobile Application to enter exclusion mode. When prompted by the controller:
3. Press the Button once.
4. Upon successful exclusion, the LED Indicator blink quickly five times and then blink five times quickly every minute.
Ring Alarm Extender is listening device and is always awake as long as it connected to line power or running on battery.
Factory reset Range Extender
If needed, the Range Extender can be reset locally by following these steps. Only do this if your Z-Wave controller is missing or otherwise unreachable. Beware that resetting your device will disconnect it from the system:
1. Make sure that your Range Extender is powered on.
2. Press and hold the Button for 10 seconds.
The Range Extender’s memory will be erased to factory settings and the LED Indicator will
blink very quickly six times and then blink once every half second until it is included in a system.
Note: Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.
Please note that this is a user manual Range Extender from Ring is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Range Extender and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.