The following is an overview of the user manual for the Z-Wave product SRT-321 (Thermostat-HVAC) (MAX10U-734)from Secure Controls. To view other Z-Wave products and manuals from Secure Controls follow that link.
Overview
By combining ease of use, ease of installation and intelligent control this thermostat is suitable for use in most heating systems.
Security
As a Z-Wave Plus certified product, SRT-321 (Thermostat-HVAC) supports Z-Wave S2 security. The following security modes are directly supported:
Features
Secure Controls describes SRT-321 (Thermostat-HVAC) as having the following features:
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
STEP 1: On the SRT321, Set DIL switch 1 on the back of the unit to 'ON' position, scroll through the function menu by rotating the dial, select ""E"" and press the dial to activate Exclusion process. Now the character ""E"" starts flashing.
STEP 2: On the 3rd party device, select Exclusion for removing device from SRT321's network.
After successful Exclusion SRT321 displayed ""EP"" other wise displayed ""EF"" (Exclusion fail).
Note: Once the character starts flashing the installer has 60 seconds to activate the 3rd party device.
After successful Exclusion set DIL switch 1 to 'OFF' position to operate SRT321 in normal operation.
If the Exclusion process has failed more than once, try moving the SRT321 to another position and repeat the Exclusion steps.
STEP 1: On the SRT321, set DIL switch 1 on the back of the unit to 'ON' position, scroll through the function menu by rotating the dial, select ""I"" and press the dial to activate Inclusion process. Now the character ""I"" starts flashing.
STEP 2: On the 3rd party device, select Inclusion for adding a device into SRT321's network.
After successful inclusion SRT321 displayed ""IP"" other wise displayed ""IF"" (Inclusion fail).
Note: Once the character starts flashing the installer has 60 seconds to activate the 3rd party device.
After successful Inclusion set DIL switch 1 to 'OFF' position to operate SRT321 in normal operation.
If the inclusion process fails more than once, the 3rd party device may be already included in another network. So first exclude and then include the device.
Factory reset SRT-321 (Thermostat-HVAC)
Please use this procedure only when the primary controller is missing or otherwise inoperable.
To reset the thermostat Set DIL switch 1 on the back of the unit to 'ON' position, scroll through the function menu by rotating the dial, select ""P"" and press the dial twice on the target device to execute reset.
Note: After successful operation device displayed ""PP"".
It will put the device in factory default, that include setting all the configuration, Association to factory default and removing the device from Z-Wave network.
STEP 1: On the another Z-Wave controller, select Include for adding SRT321 to the network.
STEP 2: On the SRT321, Set DIL switch 1 on the back of the unit to 'ON' position, scroll through the function menu by rotating the dial, select ""L"" and press the dial to start Learn process. Now the character ""L"" starts flashing.
After successful operation SRT321 displayed ""LP"" other wise displayed ""LF"" (Learn fail).
Note: Once the character starts flashing the installer has 20 seconds to activate the 3rd party controller unit (2 seconds classic inclusion, than after 3 retries for NWI inclusion).
After successful Learn set DIL switch 1 to 'OFF' position to operate SRT321 in normal operation.
If the Learn process has failed more than once, the SRT321 may be already included in another network. So first exclude and then include the SRT321.
SRT321 will wake-up regularly and announce the wakeup state by sending Wakeup Notification to the configured node ID if Wakeup Interval and valid node ID is set.
To forcefully wake up the device to send Wakeup notification do the following steps: Set DIL switch 1 on the back of the unit to 'ON' position, and than back to the 'OFF' position.
Note: It is possible to set the node ID to 255 to send wakeup notifications as broadcast. In this mode device takes more time to go to sleep and drains battery faster, but can notify all it's direct neighbors about a wakeup.
Please note that this is a user manual SRT-321 (Thermostat-HVAC) from Secure Controls is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have SRT-321 (Thermostat-HVAC) and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.