5-Outlet Power Strip (ZEN20 VER. 2.0) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product 5-Outlet Power Strip (ZEN20 VER. 2.0)from Zooz. To view other Z-Wave products and manuals from Zooz follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions


5-Outlet Power Strip
SKU Code
ZEN20 VER. 2.0

- Z-Wave on/off control of up to 5 electrical devices
- On/off (charging/charged) reports from USB ports to the hub (no Z-Wave control) - turn off the charging device for best results
- Energy monitoring for each of the 5 outlets
- Built-in overload protection and ETL certification
- Z-Wave Plus signal repeater to extend network range
- S2 security protocol and the latest 500 Z-Wave chip for faster and safer wireless communication

- Model Number: ZEN20 VER. 2.0
- Z-Wave Signal Frequency: 908.42 MHz
- Power: 120 VAC
- Maximum Load: 15 A total (between 5 outlets)
- Maximum Load for USB ports: 2.1 A total (between 2 ports)
- Cord Length: 2 feet
- Range: Up to 100 feet line of sight
- Installation and Use: Indoor only
Version #
HW: 1 FW: 1.00 was the version certified
Certification #
Z-Wave Version


As a Z-Wave Plus certified product, 5-Outlet Power Strip supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Unauthenticated


Zooz describes 5-Outlet Power Strip as having the following features:

  • Supported Meter Type
  • Supported Notification Types
  • Electric Load Type
  • Firmware updatable via a compatible Z-Wave gateway
  • Switch Load Capacity Current
  • Color
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

1. Plug the Power Strip into a grounded receptacle you’re planning to use it at (it doesn’t need to be close to the hub)
2. Initiate inclusion (pairing) in the app (or web interface).
3. CLICK CH1 BUTTON 3 TIMES QUICKLY. All LED indicators will start flashing
4. You will see 7 or 8 new on/off devices in your app: 5 channels or on/off control, 2 channels for on/off monitoring (USB ports reporting charging/ charged status, no control), and possibly one master node to access and adjust advanced settings in.

1. Bring the strip within direct range of your Z-Wave gateway (hub).
2. Put the Z-Wave hub into exclusion mode.
3. Press and release the CH1 button 3 times quickly.
4. Your hub will confirm exclusion and all of the channels (child outlets) and the main device will disappear from your controller's device list.

Factory reset 5-Outlet Power Strip

If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, click-click-click’n’hold CH1 button for at least 10 seconds. All LED indicators will flash to confirm successful reset.
NOTE: All previously recorded activity and custom settings EXCEPT for the kWh record will be erased from the device’s memory.

USB Ports will report on/off when a connected device is charging or charged.

Please note that this is a user manual 5-Outlet Power Strip from Zooz is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have 5-Outlet Power Strip and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.