700 Toggle Dimmer (ZEN74) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product 700 Toggle Dimmer (ZEN74)from Zooz. To view other Z-Wave products and manuals from Zooz follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions


700 Toggle Dimmer
SKU Code
- Manual or Z-Wave on/off and brightness control
- NEW: 700 series Z-Wave chip for better range and faster control
- Simple Direct 3-Way: connect with existing on/off switches in 3-
way, 4-way, and 5-way set-ups, no add-on needed
- Scene control: trigger actions with multi-tap (select hubs only)
- Smart bulb mode: disable relay and control the light via Z-Wave
- Night light mode: press down when off to turn lights on to 20%
- Multi-color LED indicator for easy pairing and troubleshooting
- Works with LED and incandescent bulbs (don’t use with tubes)

- Model Number: ZEN74 VER. 1.0
- Z-Wave Signal Frequency: 908.42 MHz
- Power: 120 VAC, 60 Hz
- Maximum Load: 100 W LED, 300 W incandescent; DON’T use
with fans, switches receptacles, or tube lights
- Range: Up to 500 feet line of sight
- Operating Temperature: 32-104 F (0-40 C)
- Installation and Use: Indoor only
Version #
HW: 1 FW: 1.00 was the version certified
Certification #
Z-Wave Version


As a Z-Wave Plus certified product, 700 Toggle Dimmer supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Authenticated
  • S2 Unauthenticated


Zooz describes 700 Toggle Dimmer as having the following features:

  • Neutral Wire Required
  • Switch Load Capacity Watts
  • Color
  • Firmware updatable via a compatible Z-Wave gateway
  • Z-Wave Scene Type
  • Electric Load Type
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

SmartStart location

SmartStart QR code's location as follows: This device is equipped with a unique authentication code for trusted wireless communication. Find the full DSK key for the device on the QR sticker located on the green inner box the product came in.

1. Initiate inclusion (pairing) in the app (or web interface).
2. TAP UP 3 TIMES QUICKLY if using traditional Z-Wave inclusion.
3. The LED indicator will blink blue to signal communication and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails.

1. Bring your Z-Wave gateway (hub) close to the switch if possible
2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com)
3. Toggle the switch down 3 times quickly (the LED indicator will start blinking blue)
4. Your hub will confirm exclusion, the LED indicator on the switch will turn green for 3 seconds, and the device will disappear from your controller's device list

Factory reset 700 Toggle Dimmer

If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the toggle down for 10 seconds until the LED indicator starts blinking. Release toggle, and immediately after, toggle the switch down 5 times to complete the reset. The LED indicator will flash blue 3 times and turn red for 3 seconds to confirm successful reset.

Please note that this is a user manual 700 Toggle Dimmer from Zooz is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have 700 Toggle Dimmer and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.