Dimmer Switch 700 (ZEN72) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Dimmer Switch 700 (ZEN72)from Zooz. To view other Z-Wave products and manuals from Zooz follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions


SKU Code
- Manual or Z-Wave on/off and brightness control
- NEW: 700 series Z-Wave chip for better range and faster control
-Direct 3-Way: works with regular on/off switches in a 3-way
- Scene control: trigger actions with multi-tap (select hubs only)
- Smart bulb mode: disable relay and control the light via Z-Wave
- Night light mode: press down when off to turn lights on to 20%
- Adjustable LED indicator in 4 colors and 3 brightness levels
- Built-in Z-Wave range test tool and signal repeater
- Works with LED and incandescent bulbs (don’t use with tubes)

- Model Number: ZEN72 VER. 1.0
- Z-Wave Signal Frequency: 908.42 MHz
- Power: 120 VAC, 60 Hz
- Maximum Load: 150W LED bulbs, 960W Incandescent, 1800W -(15A) Resistive
- Range: Up to 500 feet line of sight
- Operating Temperature: 32-104° F (0-40° C)
- Installation and Use: Indoor only
Version #
HW: 1 FW: 1.00 was the version certified
Certification #
Z-Wave Version


As a Z-Wave Plus certified product, Dimmer Switch 700 supports Z-Wave S2 security. The following security modes are directly supported:

  • S2 Authenticated
  • S2 Unauthenticated


Zooz describes Dimmer Switch 700 as having the following features:

  • Electric Load Type
  • Firmware updatable via a compatible Z-Wave gateway
  • Switch Load Capacity Watts
  • Z-Wave Scene Type
  • Color
  • Neutral Wire Required
  • FLiRS capable
  • Supports Network Wide Inclusion
  • Supports Z-Wave Explorer Frames
  • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

Installation instructions

SmartStart location

SmartStart QR code's location as follows: on Page 2 under Z-Wave Control > Add Device (visual cue to the location of the QR code on the switch)

1. Initiate inclusion (pairing) in the app (or web interface).
2. TAP UP 3 TIMES QUICKLY if using traditional Z-Wave inclusion.
3. The LED indicator will blink blue to signal communication and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails.

1. Bring your Z-Wave gateway (hub) close to the switch if possible
2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com)
3. Tap the lower paddle on the switch 3 times quickly (the LED indicator will start blinking blue)
4. Your hub will confirm exclusion, the LED indicator on the switch will turn green for 3 seconds, and the device will disappear from your controller's device list

Factory reset Dimmer Switch 700

If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the lower paddle for 10 seconds until the LED indicator starts blinking. Release paddle, and immediately after, tap the lower paddle 5 times to complete the reset. The LED indicator will flash blue 3 times and turn red for 3 seconds to confirm successful reset.

Please note that this is a user manual Dimmer Switch 700 from Zooz is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Dimmer Switch 700 and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.