Z-Wave Dimmer Light Switch (ZEN22) manual for Z-Wave

The following is an overview of the user manual for the Z-Wave product Z-Wave Dimmer Light Switch (ZEN22)from Zooz. To view other Z-Wave products and manuals from Zooz follow that link.

  1. Overview
  2. Security
  3. Features
  4. Installation instructions


Zooz Z-Wave Dimmer Light Switch
SKU Code
- Manual or remote on/off control and dimming from your mobile device or computer (when included to a Z-Wave gateway controller)
- Z-Wave Plus with improved 500 chip for faster and safer wireless communication
- Works with most high-quality DIMMABLE LED, CFL, and incandescent bulbs
- Based on universal command classes - supported by most Z-Wave controllers
- May be associated and grouped with other Z-Wave devices for advanced home automation
- LED indicator to help locate the switch in dark space
- Simple elegant design with screwless snap-on wall plate included
- Built-in Z-Wave signal repeater for a stronger and more reliable network

Model Number: ZEN22
Z-Wave Signal Frequency: 908.42 MHz
Power: 120 VAC, 60 Hz
Maximum Loads: 500W Single-gang, 400W Double-gang, 300W Triple-gang Incandescent, 150W CFL or LED
Range: Up to 100 feet line of sight
Operating Temperature: 32-104° F (0-40° C)
Installation and Use: Indoor only
Version #
HW: 1 FW: 20.15 was the version certified
Certification #
Z-Wave Version


As a Z-Wave Plus certified product, Z-Wave Dimmer Light Switch supports Z-Wave S2 security. The following security modes are directly supported:


    Zooz describes Z-Wave Dimmer Light Switch as having the following features:

    • Color
    • Electric Load Type
    • Switch Load Capacity Watts
    • Neutral Wire Required
    • Switch Type
    • FLiRS capable
    • Supports Network Wide Inclusion
    • Supports Z-Wave Explorer Frames
    • Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via

    Installation instructions

    1. Bring your Z-Wave gateway hub or controller as close to the switch as possible
    2. Put your Z-Wave controller in exclusion mode
    3. Tap the switch on and off quickly 3 times to complete the exclusion process
    4. The device should disappear from your controller's device list

    Factory reset Z-Wave Dimmer Light Switch

    The switch will be reset to factory defaults only by exclusion using a Z-Wave controller. You may use any certified Z-Wave controller to exclude and reset the switch. This device may not be reset manually when the network’s primary controller is missing or otherwise inoperable. NOTE: All previously recorded activity and custom settings will be erased from the device’s memory.

    1. Bring your Z-Wave gateway hub or controller as close to the switch as possible
    2. Put your Z-Wave controller in inclusion mode
    3. Tap the switch on and off quickly 3 times to finalize the inclusion process
    4. A new dimming device should appear on your controller's device list

    Troubleshooting Tips:
    If you are unable to include the Z-Wave dimmer to your controller, please try one of the following:
    - Bring the controller closer to your Z-Wave switch or use a hand-held secondary controller for inclusion
    - Tap your Z-Wave switch quicker 4 or 5 times once you put the controller in the inclusion mode to ensure the command has gone through
    - Put your controller in the EXCLUSION mode and tap the switch quickly 3 times, then try adding it to your network again

    Please note that this is a user manual Z-Wave Dimmer Light Switch from Zooz is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Z-Wave Dimmer Light Switch and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.