The following is an overview of the user manual for the Z-Wave product Z-Wave Motion and Light Mini Sensor (ZSE09)from Zooz. To view other Z-Wave products and manuals from Zooz follow that link.
Overview
- Accurate motion and light level detection
- Wireless notifications and low battery alerts (when included to a Z-Wave gateway controller)
- Custom automation scenarios based on both light and motion triggers (advanced configuration required)
- Adjustable sensitivity levels for motion detection to fit your needs
- Ultra small and simple design
- Z-Wave Plus with improved 500 chip for faster and safer wireless communication
- Flexible and quick installation
SPECIFICATIONS:
Model Number: ZSE09
Z-Wave Signal Frequency: 908.42 MHz
Power: 1 CR123A battery (included)
Power Consumption: 0.15W
Operating Temperature: 32 – 104 F
Motion detection: Up to 20 feet
Range: Up to 100 feet line of sight
Installation and Use: Indoor only
Dimensions: 1.9” x 1.8”
Weight: ½ oz
Security
As a Z-Wave Plus certified product, Z-Wave Motion and Light Mini Sensor supports Z-Wave S2 security. The following security modes are directly supported:
Features
Zooz describes Z-Wave Motion and Light Mini Sensor as having the following features:
- Battery Quantity
- Battery powered using CR123A batteries
- Color
- Sensors
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
Factory reset Z-Wave Motion and Light Mini Sensor
When your network’s primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. To complete the process, make sure the Mini Sensor is powered on, then open the cover and PRESS AND HOLD the Z-Wave button for AT LEAST 10 SECONDS until the LED indicator flashes ONCE. Release the button. NOTE: All previously recorded activity and custom settings will be erased from the device’s memory.
1. Make sure the Mini Sensor is powered on and located within direct range of your Z-Wave gateway controller
2. Put your Z-Wave controller into exclusion mode
3. Press and release the Z-Wave button 3 TIMES quickly. The LED indicator will flash quickly
4. The Mini Sensor should disappear from your controller's device list
1. Bring the Mini Sensor within direct range of your controller
2. Carefully turn and lift the cover of your Mini Sensor to access the battery
3. Remove the plastic pull-tab from the battery slot. The LED indicator will blink slowly
4. Put your Z-Wave controller into inclusion mode
5. Press and release the Z-Wave button on the Contact Sensor 3 TIMES quickly. The LED indicator will flash quickly
6. A new motion and light sensor will appear on your controller's device list
Troubleshooting Tips
If you are unable to include the Z-Wave Mini Sensor to your controller, please try one of the following:
- Bring the Mini Sensor closer to your Z-Wave controller
- Once in inclusion mode, press and release the Z-Wave button quickly 6-7 TIMES to ensure the command has gone through
- Put your controller into EXCLUSION mode. Press and release the Z-Wave button quickly 3 TIMES, and then try adding it to your network again
If you change settings and parameters for the sensor, you may need to wake it up manually for the changes to be recorded. Press and release the Z-Wave button ONCE to wake the device up. The LED indicator will flash ONCE.
The sensor’s wake-up interval is set to 12 hours by default to save battery life. Though not recommended, you can change the wake-up interval using your controller’s advanced settings if available. Minimum value: 300s (5 minutes), maximum value: 16,777,200s (around 194 days). Accepted values need to match minute intervals, so 300, 360, 420, etc.
Please note that this is a user manual Z-Wave Motion and Light Mini Sensor from Zooz is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Z-Wave Motion and Light Mini Sensor and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.