The following is an overview of the user manual for the Z-Wave product Z-Wave Smart Plug (ZEN06)from Zooz. To view other Z-Wave products and manuals from Zooz follow that link.
Overview
- Manual and remote on / off control
- Energy monitoring
- Scene inclusion for custom automation scenarios when included to a Z-Wave gateway controller
- LED indicator displaying Z-Wave signal strength and power usage
- Security enabled Z-Wave device with AES signal encryption (requires a security enabled gateway controller for full functionality)
- Z-Wave Plus with improved 500 chip for faster and safer wireless communication
- Built-in range extender for a stronger, more reliable network
- 2 USB charging ports for your smart phone or tablet (no Z-Wave functionality)
- Built-in overload protection in Z-Wave outlet and USB ports
Product Specifications:
Model Number: ZEN06
Z-Wave Signal Frequency: 908.42 MHz
Power: 110V, 60Hz
Maximum Load: 15A, 1800W
USB Charging Port Power: 1A and 2.4A
Operating Temperature: 14 – 104 F
Range: Up to 130 feet line of sight
Installation and Use: Indoor only
Dimensions: 4” x 2.5” x 1.2”
Weight: 7oz
Security
As a Z-Wave Plus certified product, Z-Wave Smart Plug supports Z-Wave S2 security. The following security modes are directly supported:
Features
Zooz describes Z-Wave Smart Plug as having the following features:
- Color
- Electric Load Type
- Firmware updatable via a compatible Z-Wave gateway
- Switch Load Capacity Volt-Ampere
- Switch Load Capacity Watts
- FLiRS capable
- Supports Network Wide Inclusion
- Supports Z-Wave Explorer Frames
- Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via
Installation instructions
1. Plug the smart plug into a grounded receptacle located within 3 feet from your Z-Wave gateway controller
2. Put your Z-Wave controller in exclusion mode
3. Press and release the Z-Wave button 3 TIMES QUICKLY
4. LED indicator will flash orange
5. The smart plug should disappear from your controller's device list and LED indicator will remain solid orange for a few seconds to indicate exclusion
Auto Z-Wave Inclusion
1. Put your Z-Wave controller in inclusion mode
2. Plug the smart plug into a grounded receptacle located within 3 feet from your Z-Wave gateway controller
3. LED indicator will flash blue
4. A new on / off device should be recognized by your Z-Wave controller
Manual Z-Wave Inclusion
1. Plug the smart plug into a grounded receptacle located within 3 feet from your Z-Wave gateway controller
2. Put your Z-Wave controller in inclusion mode
3. Press and release the Z-Wave button 3 TIMES QUICKLY
4. LED indicator will flash blue
5. A new on / off device should be recognized by your Z-Wave controller
Secure Z-Wave Inclusion
1. Plug the smart plug into a grounded receptacle located within 3 feet from your Z-Wave gateway controller
2. Put your Z-Wave controller in secure inclusion mode
3. Press and HOLD the Z-Wave button for at least 3 seconds
4. LED indicator will flash green
5. LED indicator will turn solid green once the inclusion is completed. Please allow 5 minutes for configuration. DO NOT press any buttons or move the device during that time
6. A new secure on / off device should be recognized by your Z-Wave controller
LED NOTIFICATIONS
LED indicator on your smart plug will visually report power consumption and network range.
How to read LED indicator colors?
Burgundy = Smart Plug is off
Blue = 0 – 300 W
Cyan = 300 – 600 W
Green = 600 – 900 W
Yellow = 900 – 1200 W
Red = 1200 – 1500 W
Purple = 1500 – 1800 W
Purple blink = over 1800 W
LED Indicator Control
Parameter 27: You can choose how the LED indicator displays power consumption on the smart plug
Values: 0 – LED indicator will display power consumption whenever the device is plugged in (LED stays on at all times – default setting); 1 – LED indicator will display the level of power consumption for 5 seconds only whenever the device is turned on or off (LED indicator will stay off for most of the time)
Size: 1 byte dec.
How to test Z-Wave network range for my Smart Plug?
You can easily check if the Smart Plug is within your Z-Wave controller’s range. Here is how:
Press and hold the Z-Wave button for 6 to 9 seconds until the LED indicator turns violet. The LED indicator will then report signal strength.
Flashing green = direct communication with the primary controller is established and still being diagnosed
Solid green for 2 seconds = direct communication with the primary controller is stable
Flashing orange = direct communication with the primary controller is intermittent and being diagnosed
Solid orange = communication quality is fair
Solid red = communication with the primary controller has failed
Press and release the Z-Wave button to exit testing mode.
NOTE: This function may only be activated once the Smart Plug has been included to a Z-Wave network.
Factory reset Z-Wave Smart Plug
When your network’s primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, plug the smart plug into a grounded receptacle, then PRESS AND HOLD the Z-Wave button for AT LEAST 20 SECONDS. The LED indicator will stay solid yellow for 2 seconds to indicate successful reset. The plug will then automatically turn off.
NOTE: All previously recorded activity and custom settings will be erased from the device’s memory. You may only reset your smart plug once it has been included to a Z-Wave network.
Please note that this is a user manual Z-Wave Smart Plug from Zooz is provided as is and without warranty; all information contained herein is provided by the manufacturer or the certifying body. The information provided is for reference only and is not intended to be used as a substitute for professional advice. ZWaveProducts.com only warrants and is only able to support products purchased directly from us. If you have Z-Wave Smart Plug and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.